AMX Stereo System DAS AMFM User Manual

Installation Guide  
DAS-AMFM AM/FM Tuner Module  
Note: The ribbon cable must be oriented so that the red stripe is con-  
Overview  
nected to Pin 1 on the connector.  
Add AM/FM Radio functionality to your Mi Series system with the  
DAS-AMFM AM/FM Tuner Module (FG1110-01).  
Up to two DAS-AMFM modules can be added to each Mi Series  
controller.  
Rear of controller  
Each tuner module uses one source input on the audio controller.  
WARNING: Disconnect all power sources before opening the chassis. Fail-  
ure to disconnect power before performing this installation may cause injury  
or death.  
Tuner 1 Connector  
CAUTION: Make sure to discharge all static electricity from your body  
before touching any components of the tuner modules or the audio control-  
ler. Failure to do so may lead to permanent damage to the tuner or  
controller.  
FIG. 3 Tuner 1 Module Connection  
Be sure that both ends of the cable are securely plugged into their  
respective boards through the 20-pin connectors (FIG. 4).  
Single Tuner Installation Instructions  
Installing The Tuner Module in the Controller  
1. Remove the cover from the controller.  
2. With the back of the unit facing you, remove the screws from the  
Tuner Option cover plate at the right top corner of the rear panel  
(FIG. 1) and remove the plate. Retain the screws, as they will be used  
to install the tuner.  
Tuner 1 (installed)  
FIG. 4 20-Pin Connector and Ribbon Cable  
Setting the Jumpers in the Controller  
Examine the configuration of the jumpers on the left end of the rear board,  
as seen when viewing the rear board from the front of the controller.  
Tuner Option  
cover plate  
The jumpers should be in the “Off” position, with the top pair of pins in each  
configuration exposed and the jumpers connecting the second and third set  
of pins.  
FIG. 1 Rear Panel Tuner with Tuner Option cover plate  
Move the top set of jumpers to the “On” position, connecting the first two  
3. Carefully insert the DAS-AMFM tuner module into the controller, with  
the electronics facing up, and use the screws that attached the Tuner  
Option cover plate to secure the tuner to the controller.  
Tuner 1 jumpers (in “On” position)  
Exposed pair of pins  
Note: Be careful not to damage the white ribbon cable on the top of  
the Tuner module.  
4. Place the Rear Panel connector at the end of the ribbon cable (FIG. 2)  
on the rear board pin-bus, keeping the red stripe at the top.  
not used  
RED STRIPE (to Pin 1)  
Tuner 2 jumpers (in “Off” position)  
Tuner 1  
Rear Panel  
FIG. 5 Controller Jumper Configuration  
Tuner 2  
Reconnect power to the unit and turn it on to make sure that the tuner  
is properly integrated with the controller.  
FIG. 2 Tuner Ribbon Cable  
5. Connect the "Tuner 1" connector on the ribbon cable to the Tuner 1  
If the tuner is functioning properly, remove power and replace the unit  
cover.  
 
         

Acclaim Lighting Universal Remote X FADE 6 User Manual
Adcom Universal Remote URC 200 User Manual
Agri Fab Lawn Mower 45 0265 User Manual
Allied Telesis Switch AT GS900 16 User Manual
Amana Refrigerator A4TXNWFW User Manual
AMX TV Converter Box AXB REL8 User Manual
Atlona Stereo Amplifier AT VGA300RL AT VGA10SS User Manual
Audiovox Automobile Alarm PRO 9842B User Manual
Axor Plumbing Product 42260000 User Manual
Behringer Microphone C 1U User Manual